Pig Carcass Singeing Furnace Machine

In a pig plant, the Pig Carcass Singeing Furnace Machine serves as a carcass‑finishing station that removes remaining hair or surface residue after primary dehairing. The final build must match the actual product load, room layout and cleaning routine at site. The HT listing supplies reference data for the offered arrangement; those figures are reproduced below for comparison. For export quotations, confirm voltage, materials, guarding, spare parts and documentation before the purchase order is released.

Product Overview

Working Principle

The carcass passes rotating polishing elements, trimming positions or a controlled flame zone. Exposure is limited to the surface treatment needed before final washing and clean‑line entry. Operators need a clear stop‑and‑recovery routine for a jam, tool change or hygiene break.

Main Features

More uniform carcass finish
Adjustment for carcass size and line speed
Contained residue or exhaust
Guards around moving or hot parts
Easy access for cleaning
Integration with the overhead rail

Technical Specifications

Parameter	Reference Value / Buyer Check
Model	HT‑P403
Application	Which main used to burn remnant hair on pig carcass skin
Work pressure	0.3‑0.5 MPA
Liquefied gas Consumption	0.3‑0.5 kg / Pig
Out size	230015004300mm(LWH)
Max capacity	300‑400 Heads per hour
Component and material	1）3mm stainless steel plate 2） 4pcs gas / air mixed columns 3）28pcs flame nozzles 4）Stainless steel chimney 5）Stainless steel gas pipeline and various valves and sensors 6）Independent central control central 7）Protection against excessive gas pressure 8）Gas leakage protection
Quotation control	Specify line speed, carcass range, upstream dehairing result, required finish, exhaust or gas supply, fire controls and downstream washer position.

Reference configuration transcribed and normalized from the cited HT product page; confirm the final quotation and approved drawing.

Application

The usual application is pig slaughter lines between primary dehairing and final carcass washing. It can be specified for a new line or adapted to a retrofit, provided that the existing supports, working heights, utilities and control signals are measured on site. Plants handling several pig sizes should state the full range rather than quoting only an average.

Application Case

Illustrative reference case-A regional pork processor planning for 120 pigs per hour places the pig carcass singeing furnace machine between the relevant upstream and downstream stations. Before fabrication, the project team freezes the interface drawing, utility points and operator access. The acceptance check covers dry running, representative‑load operation, emergency stops, cleaning access and a spare‑parts handover.

Advantages

1. Fits into a defined process stage, which makes line balancing and internal linking easier.
2. Project‑specific dimensions reduce awkward field modifications at installation.
3. Service points and replaceable wear parts can be agreed before shipment.
4. Hygiene and drainage requirements can be reviewed with the equipment layout.
5. Reference source data remains visible instead of being converted into unsupported marketing claims.

Pig Carcass Singeing Furnace Machine FAQ

What information is needed to quote the Pig Carcass Singeing Furnace Machine?

Specify line speed, carcass range, upstream dehairing result, required finish, exhaust or gas supply, fire controls and downstream washer position.

Can it be connected to an existing slaughter line?

Usually yes, but a retrofit needs measured drawings. Share the rail or conveyor interface, floor levels, travel direction, available space, utilities and current control method before engineering starts.

Which spare parts should be ordered with the machine?

Start with the normal wear and hygiene parts for this duty: bearings, seals, sensors, chains or belts, nozzles, blades, scrapers, pneumatic parts and electrical protection devices as applicable. The supplier should issue a model-specific list.

Are the published technical figures final?

No. The table records reference information from the citedHTpage. Capacity, power, dimensions, material grade and utilities must be confirmed on the quotation and approved drawing.

How should the equipment be accepted after installation?

Use a documented site-acceptance test covering alignment, guards, emergency stops, interlocks, dry running, representative load, cleaning access, leakage or drainage, operator training and delivery of manuals and spares.